IT Infrastructure Installation in Edmonton and Alberta
The physical layer of IT gets neglected because it is invisible when it works. Equipment ends up on a shelf in a storage room with no ventilation, on a power circuit shared with a kettle, with cabling that nobody can trace. It runs for a while. Then a heat event, a power blip or a failed drive turns a small problem into a long outage, and the cost of doing it properly the first time looks very reasonable in hindsight.
We install and rebuild the infrastructure layer: racks and enclosures, power distribution and battery backup, ventilation and thermal management, network hardware, storage and backup systems, and the cabling that ties it together. The point is not the hardware itself — it is that six months later someone can open the rack, read the labels, and understand what they are looking at.
This work suits businesses setting up new premises, outgrowing an improvised setup, or inheriting infrastructure that was never documented. We work alongside your existing IT provider where you have one, since the physical build and the systems administration are different jobs.
Who This Service Is For
The situations where this work is usually the right answer.
Businesses fitting out new premises
New offices and facilities where the server room, rack, power and cabling need to be specified before the space is finished.
Sites that have outgrown a closet
Equipment accumulated on shelves with no ventilation, no protected power and no documentation, now carrying more than it was ever meant to.
Organisations with no backup or protection
Sites with no UPS, no tested backups and single points of failure that nobody has quantified.
Companies with existing IT support
Businesses whose IT provider handles systems and software but does not do physical installation, cabling or rack work.
What the Installation Includes
Everything below is part of a standard engagement, not a list of chargeable extras.
- Assessment of existing equipment, power, ventilation and physical security
- Rack or enclosure specification sized for current equipment plus growth
- Rack installation, levelling, and floor or wall fixing
- Rack-mount and shelf mounting of servers, switches, storage and appliances
- Power distribution units with adequate circuit capacity and load balance
- UPS sizing, installation and runtime calculation for a controlled shutdown
- Surge protection and coordination with the building's electrical supply
- Ventilation and thermal assessment, with airflow management in the rack
- Structured cabling and patch panel termination inside and to the rack
- Cable management so airflow is not obstructed and runs can be traced
- Backup system installation with a restore actually tested, not just configured
- As-built documentation: rack elevation, power schedule, IP list and labelling
Our Process
How a project runs from first contact to handover.
Assessment
We review existing equipment, available power, ventilation, physical security and what the infrastructure has to support over the next few years.
Design and specification
Rack layout, power and UPS sizing, cooling requirement and cabling are documented and quoted before anything is ordered.
Build and installation
Rack installed and equipment mounted in a deliberate elevation, with power distribution, protection and cabling installed and dressed.
Migration and commissioning
Existing equipment is migrated in a scheduled window, systems verified under load, and thermal behaviour checked once everything is running.
Documentation and handover
Rack elevation drawing, power schedule, port map and labelling handed over — to you or directly to your IT provider.
Equipment We Support
- Racks and enclosures
- Floor-standing, wall-mount and open-frame racks, with lockable enclosures where equipment sits in an area staff or the public can reach.
- UPS and power distribution
- Battery backup sized for a controlled shutdown or for ride-through of short events, with managed PDUs providing per-outlet control and load visibility.
- Servers, storage and backup
- Rack-mount servers, network-attached storage and backup appliances, installed with a restore tested rather than a backup job merely scheduled.
- Network hardware
- Switching, firewalls and routers mounted, powered and cabled to match the network design, with uplinks and management ports clearly identified.
- Environmental monitoring
- Temperature, humidity, leak and door sensors with alerting, so a cooling failure raises an alarm at 2am instead of being discovered at 8am.
Where We Work
IT infrastructure installation across Edmonton, Sherwood Park, St. Albert, Spruce Grove, Leduc, Nisku and Fort Saskatchewan, with project work at commercial and industrial sites throughout Alberta.
See every area we serve across Alberta- Edmonton
- Sherwood Park
- St. Albert
- Spruce Grove
- Leduc
- Fort Saskatchewan
- Calgary
- Red Deer
- Grande Prairie
- Fort McMurray
Frequently Asked Questions
Common questions about it infrastructure installation in Edmonton and across Alberta.
Related Services
Work that commonly goes with this, and that we handle at the same time.
Structured Cabling
Cat6, Cat6A and fibre cabling installed to standard, terminated to labelled patch panels, tested and documented.
Structured CablingCommercial Network Installation
Designed and installed business networks: switching, routing, VLAN segmentation, firewalls, PoE and internet failover built to survive a working day.
Commercial Network InstallationWi-Fi Installation
Surveyed access point layouts that fix dead zones properly — for houses, offices, warehouses, metal shops and outdoor yards.
Wi-Fi InstallationCradlepoint Installation
Cradlepoint LTE and 5G routers installed and configured for automatic internet failover, remote sites and in-vehicle networks.
Cradlepoint Installation
Request a Quote
Tell us about the site and what you need. We will come back to you with a straight answer about what the work involves and what it costs.