Wi-Fi Installation and Coverage Design in Edmonton
Nearly every Wi-Fi complaint gets treated as a hardware problem. The router is replaced, then a mesh kit is added, then an extender, and the dead zone in the back bedroom or the far end of the shop is still there. The underlying issue is almost never the brand of equipment — it is that nobody measured the building.
Wi-Fi is radio, and radio is shaped by what it passes through. Concrete, brick, foil-backed insulation, metal cladding, mirrors, tile and heated floors all attenuate signal in ways a floor plan does not reveal. Two houses with identical square footage can need completely different access point counts. So can two halves of the same warehouse.
We survey the building, measure actual signal and interference rather than estimating from area, and design a layout that puts access points where they are needed and wires them properly. Extenders halve throughput and mesh backhaul degrades with every hop; a wired access point does neither. Where running cable is genuinely impractical we say so and design the best wireless backhaul available, but we start from measurement either way.
Who This Service Is For
The situations where this work is usually the right answer.
Homes with dead zones
Larger houses, older houses with plaster and lath, bungalows with finished basements, and anywhere the single ISP router was never going to be enough.
Offices and client-facing businesses
Sites needing reliable staff coverage plus a separate guest network that does not expose internal systems.
Warehouses, shops and metal buildings
Structures where steel cladding, racking and high ceilings defeat consumer equipment entirely and coverage has to be engineered.
Outdoor yards and multi-building sites
Storage yards, acreages and campuses needing outdoor-rated access points or point-to-point links between buildings.
What the Installation Includes
Everything below is part of a standard engagement, not a list of chargeable extras.
- On-site survey measuring signal strength, noise floor and channel congestion
- Identification of construction materials that will attenuate signal
- Access point count and placement plan based on measurement, not floor area
- Ethernet cabling to each access point for wired backhaul
- Power over Ethernet so access points need no local power outlet
- Ceiling, wall and outdoor-rated mounting as the location requires
- Channel planning and transmit power tuning to limit self-interference
- Band steering and roaming configuration so devices hand off cleanly
- Separate guest network isolated from internal systems
- Wi-Fi 6 / 6E configuration where client devices support it
- Point-to-point bridging between buildings where cable cannot be run
- Post-installation walk test confirming coverage in every area you use
Our Process
How a project runs from first contact to handover.
Coverage survey
We walk the site with survey tools, map existing signal and interference, and find where coverage actually fails rather than where it is assumed to.
Layout design
We produce an access point layout with counts, positions, mounting types and cable routes, sized to the building's construction and how you use the space.
Cabling and mounting
Ethernet is run to each position and terminated, and access points are mounted to ceiling, wall or outdoor hardware and powered over the same cable.
Tuning and verification
Channels, power levels, roaming and guest isolation are configured, then we walk the site again and confirm real coverage and throughput in every area.
Equipment We Support
- Controller-managed access points
- Business access points managed as one system, so channel, power and roaming decisions are coordinated instead of each unit competing with its neighbours.
- Wi-Fi 6 and 6E hardware
- Current-generation access points that handle dense client counts far better than older equipment, plus 6 GHz where client devices can use it.
- Outdoor and industrial access points
- Sealed, temperature-rated units for yards, loading areas, unheated shops and exterior mounting through Alberta winters.
- Point-to-point wireless bridges
- Directional links carrying network between buildings across a yard or property where trenching cable is impractical.
- PoE switching
- Switches with PoE budget sized for the access point count, so the wireless layer has one power source and one place to reboot from.
Where We Work
Wi-Fi surveys and installations across Edmonton, Sherwood Park, St. Albert, Spruce Grove, Leduc and Fort Saskatchewan, plus acreages, farms, shops and industrial sites throughout Alberta.
See every area we serve across Alberta- Edmonton
- Sherwood Park
- St. Albert
- Spruce Grove
- Leduc
- Fort Saskatchewan
- Calgary
- Red Deer
- Grande Prairie
- Fort McMurray
Frequently Asked Questions
Common questions about wi-fi installation in Edmonton and across Alberta.
Related Services
Work that commonly goes with this, and that we handle at the same time.
Commercial Network Installation
Designed and installed business networks: switching, routing, VLAN segmentation, firewalls, PoE and internet failover built to survive a working day.
Commercial Network InstallationStructured Cabling
Cat6, Cat6A and fibre cabling installed to standard, terminated to labelled patch panels, tested and documented.
Structured CablingStarlink Installation
Obstruction surveys, secure mounting, weather-sealed cable entry and full network setup for Starlink dishes on homes, businesses and remote sites.
Starlink InstallationIT Infrastructure Installation
Server rooms and equipment racks built properly: power, cooling, protection, cabling and documentation that outlast the hardware in them.
IT Infrastructure Installation
Request a Quote
Tell us about the site and what you need. We will come back to you with a straight answer about what the work involves and what it costs.